Topaz
We recommend all DVO Suspension service should be performed by a qualified bicycle mechanic. Terrain, location and riding ability can greatly affect the interval in which maintenance should be performed. Always inspect your products, and lean towards caution if maintenance is in question. When in doubt, consult a qualified bicycle mechanic, or contact DVO Suspension directly.[/box]
Full Service/Bleed
Below is a link to the full service/bleed guide for the TOPAZ T3AIR.
Service Intervals
Failure to properly maintain your shock will result in an accident, personal injury, or death.
We recommend all DVO Suspension service should be performed by a qualified bicycle mechanic. Terrain, location and riding ability can greatly affect the interval in which maintenance should be performed. Always inspect your products, and lean towards caution if maintenance is in question. When in doubt, consult a qualified bicycle mechanic, or contact DVO Suspension directly.
| Service | Interval | Notes |
| Inspect exterior for oil leaks or damage to the shock shaft such as pitting or chips. | Every Ride | |
| Clean any dirt or mud with soapy water & a clean towel. Do NOT use harsh solvents that can damage rubber seals. | Every Ride | Debris on the shaft body can accelerate seal wear and failure, keep shock shaft clean! |
| Inspect Sag Setting | Every Ride | Air Pressure can be reduced over time, this is a normal occurance. |
| Check mounting hardware | Regularly | Loose or worn shock hardware can damage the shock and or frame. Keep them tight! |
| Check Bladder Air Pressure | Regularly | Air Pressure can be reduced over time, this is a normal occurance. |
| Inspect Rebound Knob | Regularly | Check for a smooth and properly functioning knob. |
| Inspect Compression Lever | Regularly | Check for a smooth and properly functioning lever. |
| Replace all seals and oil change | 150 ride hours or one year | Seal kit part# 1569008 |
| Air Spring Service | 150 ride hours or one year | Air Spring Service kit part# 1569010 |
Owner’s Manual / Set Up Guide
Air Pressure
Setting the air pressure in the DVO Diamond is setting the spring rate for your fork. This is what is going to make the fork firmer or softer. Below is a base setting chart for air pressure to get you started. Set your pressure to the recommended PSI then check your SAG point. If you are sagging too much, add some air pressure, if you’re sagging too little, remove air pressure.
Proper Set Up
The Diamond uses an external negative spring adjust (OTT) to tune the beginning of the travel (sensitivity of the fork). Once you get into the mid-stroke of the fork, the air spring (air pressure) is active. This controls your mid-stroke support and your bottom out. In simpler terms, set your air pressure for your mid-stroke and bottom out then set your OTT to fine tune how it feels off the top.
How do I know how much OTT is right for my air pressure?
Lighter riders (lower air pressure) will use less OTT. (less sensitive) Heavier riders will need more OTT (more sensitive). The reason for this is because the OTT is there to counter-act the forces of a higher air pressure so you don’t loose small bump sensitivity. When you are using a lower air pressure, you don’t need as much to counter-act the air pressure. If you run too much OTT with a light air pressure, the fork will suck itself down and you will loose travel.
View one of the lower tabs to learn more about your OTT
To access the air valve you must remove the air spring cap. Attach your shock pump securely and inflate the air spring to the recommended air pressure. After you have added the proper amount of air pressure remember to securely replace the air spring cap so that no dirt or moisture can get inside.
 Access air valve by removing air cap |
 Attach shock pump to air valve and inflate to recommended pressure or proper sag is achieved |
Air Pressure Range: 90-170psi
| Rider Weight | Air Pressure |
| 120-139lbs | 54-63kg | 90-100psi |
| 140-159lbs | 64-72kg | 100-110psi |
| 160-179lbs | 73-81kg | 110-125psi |
| 180-199lbs | 82-90kg | 125-130psi |
| 200-219lbs | 91-100kg | 130-135psi |
| 220-239lbs | 100-108kg | 135-140psi |
| 240+lbs | 109kg+ | 140-170psi |
Jade X Full Service
Below is a link to the full service/bleed guide for the Jade X Coil Shock.
Topaz
We recommend all DVO Suspension service should be performed by a qualified bicycle mechanic. Terrain, location and riding ability can greatly affect the interval in which maintenance should be performed. Always inspect your products, and lean towards caution if maintenance is in question. When in doubt, consult a qualified bicycle mechanic, or contact DVO Suspension directly.[/box]
Topaz
Garnet Seat Post
Diamond
Emerald
Topaz
Owner’s Manual / Set Up Guide
Air Pressure
Setting the air pressure in the DVO Diamond is setting the spring rate for your fork. This is what is going to make the fork firmer or softer. Below is a base setting chart for air pressure to get you started. Set your pressure to the recommended PSI then check your SAG point. If you are sagging too much, add some air pressure, if you’re sagging too little, remove air pressure.
Proper Set Up
The Diamond uses an external negative spring adjust (OTT) to tune the beginning of the travel (sensitivity of the fork). Once you get into the mid-stroke of the fork, the air spring (air pressure) is active. This controls your mid-stroke support and your bottom out. In simpler terms, set your air pressure for your mid-stroke and bottom out then set your OTT to fine tune how it feels off the top.
How do I know how much OTT is right for my air pressure?
Lighter riders (lower air pressure) will use less OTT. (less sensitive) Heavier riders will need more OTT (more sensitive). The reason for this is because the OTT is there to counter-act the forces of a higher air pressure so you don’t loose small bump sensitivity. When you are using a lower air pressure, you don’t need as much to counter-act the air pressure. If you run too much OTT with a light air pressure, the fork will suck itself down and you will loose travel.
View one of the lower tabs to learn more about your OTT
To access the air valve you must remove the air spring cap. Attach your shock pump securely and inflate the air spring to the recommended air pressure. After you have added the proper amount of air pressure remember to securely replace the air spring cap so that no dirt or moisture can get inside.
|
Access air valve by removing air cap |
Attach shock pump to air valve and inflate to recommended pressure or proper sag is achieved |
Air Pressure Range: 90-170psi
| Rider Weight | Air Pressure |
| 120-139lbs | 54-63kg | 90-100psi |
| 140-159lbs | 64-72kg | 100-110psi |
| 160-179lbs | 73-81kg | 110-125psi |
| 180-199lbs | 82-90kg | 125-130psi |
| 200-219lbs | 91-100kg | 130-135psi |
| 220-239lbs | 100-108kg | 135-140psi |
| 240+lbs | 109kg+ | 140-170psi |
Jade X Full Service
Below is a link to the full service/bleed guide for the Jade X Coil Shock.
Topaz
We recommend all DVO Suspension service should be performed by a qualified bicycle mechanic. Terrain, location and riding ability can greatly affect the interval in which maintenance should be performed. Always inspect your products, and lean towards caution if maintenance is in question. When in doubt, consult a qualified bicycle mechanic, or contact DVO Suspension directly.[/box]
Topaz
Garnet Seat Post
Diamond
Emerald
Topaz